Contact Person : Ingrid
Phone Number : +86 18126235437
WhatsApp : +8618774804503
January 19, 2024
| Specification (or material number): | Material specific parameters (mm): | Pad design (mm): | Printed tin stencil design: | Notes: |
| QFP (Pitch=0.4mm) |
|
A=a+0.8,B=0.19mm P=p G1=e1-2*(0.4+a) G2=e2-2*(0.4+a) |
The pin length is changed from a+0.70mm to a+0.80mm, which is good for repair and printed pull tip handling. For the height of 3.8mm LQFP pad design width is used 0.23mm (stencil opening width 0.19mm) |
|
| QFP (Pitch=0.3mm) |
|
A=a+0.7,B=0.17mm P=p G1=e1-2*(0.4+a) G2=e2-2*(0.4+a)
|
T=0.10mm. Pin opening width 0.15mm |
|
| PLCC (Pitch≧0.8mm) |
|
A=1.8mm,B=d2+0.10mm G1=g1-1.0mm, G2=g2-1.0mm, P=p |
||
| BGA Pitch=1.27mm, Ball diameter: Φ=0.75±0.15mm |
|
D=0.70mm P=1.27mm
|
Recommended stencil opening diameter is 0.75mm |
Does not represent the arrangement of the actual BGA bottom solder balls |
| BGA Pitch=1.00mm, Ball diameter: Φ=0.50±0.05mm |
|
D=0.45mm P=1.00mm |
Recommended stencil opening diameter is 0.50mm |
Does not represent the arrangement of the actual BGA bottom solder balls |
| BGA Pitch=0.80mm, Ball diameter: Φ=0.45±0.05mm |
|
D=0.35mm P=0.80mm
|
Recommended stencil opening diameter is 0.40mm |
Does not represent the arrangement of the actual BGA bottom solder balls |
| BGA Pitch=0.80mm, Ball diameter: Φ=0.35±0.05mm |
|
D=0.40mm P=0.80mm |
Recommended stencil opening diameter is 0.40mm |
Does not represent the arrangement of the actual BGA bottom solder balls |
| BGA Pitch=0.75mm, Ball diameter: Φ=0.45±0.05mm |
|
D=0.3mm P=0.75mm |
Recommended stencil opening diameter is 0.40mm |
Does not represent the arrangement of the actual BGA bottom solder balls |
| BGA Pitch=0.75mm, Ball diameter: Φ=0.35±0.05mm |
|
D=0.3mm P=0.75mm |
Recommended stencil opening diameter is 0.35mm |
Does not represent the arrangement of the actual BGA bottom solder balls |
| LGA (Ball-less BGA) Pitch=0.65mm, Pin diameter: Φ=0.3±0.05mm |
|
D=0.3mm, P=0.65mm |
Recommended stencil 1:1 opening |
Does not represent the arrangement of the actual BGA bottom solder balls |
| QFN （Pitch≧0.65mm） |
|
A=a+0.35,B=d+0.05 P=p,W1=w1,W2=w2 G1=b1-2*(0.05+a) G2=b2-2*(0.05+a)
Design independent pads for each pin. Note: If the ground pad to design the thermal over-hole, it should be 1.0mm-1.2mm gap evenly distributed in the central thermal pad, over-hole should be connected to the PCB inner metal ground layer, over-hole diameter recommended for 0.3mm-0.33mm |
It is recommended that the stencil pin opening length direction flare 0.30mm, ground pad opening bridge, bridge width 0.5mm, the number of bridges W1/2, W2/2, take the integer.
If the pad design has holes, stencil openings to avoid holes, grounding pad opening area of 50% to 80% of the grounding pad area can be, too much tin on the pin welding has a certain impact |
|
| QFN （Pitch<0.65mm） |
A=a+0.3,B=d, P=p W1=w1,W2=w2 G1=b1-2*(0.05+a) G2=b2-2*(0.05+a) |
It is recommended to flare 0.20mm in the direction of the stencil pin opening length, and the rest as described above |
||
| HDMI (6100-150002-00) |
|
|
It is recommended that the stencil opening pin width in accordance with 0.27mm opening, pin length direction outward expansion 0.3mm opening |
|
| HDMI (6100-151910-00) |
|
|
It is recommended that the stencil opening pin width in accordance with 0.27mm opening, pin length direction outward expansion 0.3mm opening |
When trial production pay attention to see if the size design is suitable |
| HDMI (6100-151910-01) |
|
|
It is recommended that the stencil opening pin width in accordance with 0.265mm opening, pin length direction outward expansion 0.3mm opening |
|
| 5400-997000-50 |
|
|
It is recommended that the stencil pins be opened at 0.6mm in width and 0.4mm outward in the direction of the pin length. |
Enter Your Message
| Golden Triangle Group Ltd |
| Address: 4F, No.5 Building, Dingfeng Technology Park, Shayi Community, Shajing Town, Baoan District, Shenzhen, Guangdong Province, China |
| 86-0755-85275761 |
| sales27@gtpcb.com |
